What Does It Mean When Service Airbag Light Comes On In A Dodge Dart

Airbag Light on — Service Airbag Message GM

What causes Airbag Light on or Service Airbag Message

GM campaign to fix Airbag Light on or Service Airbag Bulletin

GM has issued a service campaign bulletin #10085D for the vehicles listed below. The bulletin accost a problem with the electric connectors for the airbag arrangement that causes an Airbag Light on or Service Airbag Message to announced. GM will replace the worn/defective connector parts for complimentary equally long as your vehicle VIN number is covered by the bulletin (run across below for compatibility)

Airbag low-cal on symptoms

The airbag connectors on some 2008 Buick Enclave, GMC Acadia, and Saturn OUTLOOK vehicles, and 2010 Chevrolet Malibu and Pontiac G6 vehicles may article of clothing, leading to corrosion in the connector terminal pins at the connection betwixt the trunk main wiring harness and the front driver and passenger side impact air bag. The clothing and corrosion changes the resistance value and that results in an Airbag calorie-free on or a service air pocketbook bulletin on the Driver Information Center (DIC).

When that happens, the seat side impact air bag is fully functional. Still, if you lot ignore the alarm light, over time the resistance can increment to a level where the seat side impact air bag may non deploy in a side impact crash.

Fix airbag light on

Dealers will replace the front seat-mounted side bear upon airbag terminals and connector trunk. If your dealer volition not encompass the repair, contact the GM client service centre.

Affected vehicles

2008 Buick Enclave VIN 8J162224—8J266444

2010 Chevrolet Malibu VIN A4100001—A4166698

2010 Chevrolet Malibu VIN AF100056—AF271265

2008 GMC Acadia VIN 8J162223—8J266443

2010 Pontiac G6 VIN A4100002—A4166963

2008 Saturn OUTLOOK VIN 8J162227—8J66442

2010 CHEVROLET MALIBU AND 2010 PONTIAC G6

Airbag Repair Procedure

1. Disable the airbag system.

2. Supersede connectors on both driver and passenger seats. Then reroute and adhere the harnesses to the seat using the service kit.

2. Disconnect connector C308 from driver'south seat cross-axle.

3. Remove the driver's seat.

4. Cut both wires from the trunk harness connector and seat airbag harness connector as close to the connector housing as possible to minimize wire length loss.

5. Slide the conduit away and remove the tape.

6. Slide the wire seals onto all 4 leads, back enough to enable removal of the insulation. Install the blue seals on the body harness and the white seals on the seat airbag harness. Strip the insulation off all four leads 5 mm (3/16 in). Align the seals with the wire insulation.

airbag light on

Relacement airbag terminals

seven. On the body harness, position two Female terminals onto the wires. Crimp the terminals onto the bare wire. Repeat the procedure using 2 MALE terminals on the seat airbag harness.

8. Position the wire seal to the terminal and crimp the seal and insulation.

ix. Solder all four terminals at the wire crimp. WARNING: DO NOT utilise soldering equipment that is battery or electric powered. These types of soldering irons can induce voltage into the excursion, which may crusade inflator module deployment and/or damage to electrical components. Use a butane fueled soldering fe when working on SIR circuits.

10. Slide the two seat airbag harness terminals through the opening of the orange connector position assurance.

xi. Slide all four terminals (2) into the advisable connector body every bit shown in the illustration. Install the blueish final position balls (TPA) devices onto the connector ends.

12. Install the gray connector clip onto the appropriate connector body.

13. Add together NyoGel 760 lubricant (dielectric lubricant) to the terminals on both sides of the connections.

14. Wrap Woven Polyester Electrical Tape (PET) (preferred) or equivalent anti-abrasion record or electrical tape effectually the two exposed wires on the seat harness for a length of 30 mm (1.ii in) from the dorsum of the connector. Continue to wrap the tape around the back of the connector.

xv. Slide the conduit dorsum up. Wrap tape starting at the back of the connector and over the conduit for a length of 130 mm (five in).

16. Tape on the gray prune at 110 mm (four.33 in) from the back of the connector. Note that the clip orientation should exist in line with the retainer prune orientation on the connector.

17. Repeat the in a higher place procedure on the passenger seat.

Here's the Letter GM sent to Owners regarding the Airbag low-cal on and entrada/remember

Dear General Motors Client:

This notice is sent to inform you that Full general Motors is conducting a customer satisfaction program that affects your 2008 model year Buick Enclave, GMC Acadia, or Saturn OUTLOOK vehicles, or your 2010 model yr Chevrolet Malibu or Pontiac G6 vehicle.

Your 2008 model year Buick Enclave, GMC Acadia, or Saturn OUTLOOK vehicles, or your 2010 model year Chevrolet Malibu or Pontiac G6 vehicle not only meets, merely exceeds government standards for side impact protection. GM recently introduced into product, changes that add to that protection. At no charge, your dealer will make similar changes to your vehicle, which was built before the product modify.

What We Volition Do: To enhance the side impact protection, your GM dealer volition update the wiring harness for both forepart seat side impact airbags. This service will be performed for yous at no accuse.

What Yous Should Do: To limit any possible inconvenience, we recommend that y'all contact your dealer as soon as possible to schedule an appointment for this repair. By scheduling an appointment, your dealer can ensure that the necessary parts will be available on your scheduled appointment date.

If you have any questions or need any assistance, just contact your dealer or the appropriate Customer

Assist Center at the number listed below.

Courtesy Transportation: If your vehicle is within the New Vehicle Limited Warranty, your dealer may provide you lot with shuttle service or some other form of courtesy transportation while your vehicle is at the dealership for this repair. Delight refer to your Possessor Manual and your dealer for details on Courtesy Transportation.

We sincerely regret any inconvenience or concern that this situation may crusade you. We desire you to know that we will do our best, throughout your ownership experience, to ensure that your GM vehicle provides you many miles of enjoyable driving.

Jim Moloney

General Director,

Customer and Human relationship Services

Buick ane-866-608-8080 1-800-832-8425

Chevrolet 1-800-630-2438 one-800-833-2438

GMC one-866-996-9463 1-800-462-8583

Pontiac i-800-620-7668 1-800-833-7668

Saturn one-800-972-8876

Posted on March three, 2018 by Rick Muscoplat